finished construction work on the construction of a bath on its plot, it is necessary to think about the interior decoration.This is a fairly serious work, but if it the right approach, the interior bath (in the pictures, we also try to show it to you) seem fascinating process.
- choice of material for the walls
- Decorating the walls of the bath
- device floor bath
- Shelves bath
- finishing the ceiling in the bath washing compartment
- Installation of lighting in the bath
choice of material for the walls
Of course, the most important decision in this paper will be the choice of finishing material.This should not stop at the mere sight of the wood - a combination of different types of wood will make the bath a special charm and comfort.Also, when choosing the material for decoration is necessary to know its properties.Otherwise, stay in the sauna will bring pleasure instead of frustration.
To finish the waiting room rest roo
also important to consider immediately the places where the shelf will be installed where it will be placed accessories for bath procedures.After all, they are the most important elements of an ancient ritual ablutions, and are of great importance.But do not pile bath appliances, especially if the room is small, otherwise traumatic increases when visiting the baths.
Decorating the walls of the bath
Interior finish in the bath is not performed by all types of wood.And even more so no linoleum and wood chipboard in the bath should not be.This flammable materials that become toxic when heated, it is dangerous to health.For these purposes, perfectly suited alder, larch, birch, aspen, poplar, cedar, basswood or abachi.Such wood even in very hot environments are not too hot, because it has low thermal conductivity.Because she did not stand out resinous substances, and after bath procedures all dries quickly.
wood for interior finishing baths are not covered with paint or varnish, as when heated these chemical coatings certainly will evaporate, poisoning the air and negatively impacting on the human body.
most common wall in the bath covered with clapboard.This process must take place long after the walls cover mineral wool insulation and a layer of aluminum foil.Alternatively, the foil tepofol.It performs the same function, but it is much more practical and easier to install.All this will seal the room.
Also note that the lining should not be directly adjacent to the layer of foil or insulation.Between them the air gap should be formed.And so it happens because battens mounted on preset crate of timber.
Bruce (yards) mounted on the wall parallel to the floor at a distance of about 50 cm apart.This level of use.After installing the frame is coated with antiseptic.Before installing do the same with the lining.Begin laying the lining from the corner.Mounting is by means of nails, staples or klyaymerov.
If we fix linings in places locks nails, they remain invisible.
device floor bath
Once you have selected the materials for interior finishing baths, you can start to work.The process of finishing off the floor, which is mounted on joists.
Logs must be laid on brick pillars, which are installed on the sand or concrete base.
lag size - 200x200 or 250x250 mm grid pattern can be selected close to 1 m, as the load on the floor will be minimal.Floorboards used decking or edging.It should be noted that in order to keep the heat in the steam room, floor it must be above the floor level in the washing room is not less than 150 mm.
The material used planks of hardwood thickness of about 30 cm. And logs and planks for the floor covered with antiseptic to prevent the proliferation of mold and mildew.
If the rest rooms or dressing rooms allowed the use of the wooden floor, the steam bath and the washing bath offices it is not welcome.These places are constantly under the influence of hot water and steam, so the tree will quickly into disrepair.In addition, the wood floor is always dirty, as it is very difficult to clean.
therefore an ideal material for finishing the floor in the steam room will be ceramic tiles.Due to the fact that hot air rises, at floor level keeps the temperature close to 30 degrees, which means that any discomfort it will bring.To his feet slipping on the tiles, you can build a small wooden reshetochki that after bath procedures endure outward so that they dry out in the open air.
Sex in the bath made with a slight slope (1: 100) and equipped with drain that excess moisture does not stagnate.
in any bath must be shelves and benches, where you can sit or lie down.As a rule, they are made of round shape - this type is the most convenient and attractive.But the most important requirements that apply - this is their reliability and durability: shelves should not creak and wobble.Material - softwood containing no resin pockets and has a light and pleasant odor.Shelves can be made with their own hands or buy ready-made in specialty stores.If you're wondering how to look interior baths, photos posted below, it will show.
surface of the lining and trim boards for shelves carefully cleaned and sanded to make it perfectly flat.Boards or battens fixed to a predetermined column from the beam.On the seat materials are beaten with a small gap, so that moisture does not stagnate, and the wood dries well.For fasteners used either wooden pegs or nails that pierce deeper, to touch them does not cause burns.
shelves in the bath has a two or three tier.This so-called speed design.The second option - L-shaped arrangement of shelves: one wall two stages, the other - only one.Option "compartment" when the top shelf is located on the bottom, like a train, good for small spaces.
Dimensions of shelves in the bath depends on the size of the room.The average is up to 2 m long and 60-90 cm in width.From the top shelf to the ceiling should be at least 1 - 1.20 m from the upper stage to the middle and from the middle to the lower - 0.4-0.6 m.
finishing the ceiling in the bath
material used forwalls, used for the ceiling.Since the ceiling will be maximally high temperature, the material for its finish should contain a minimum quantity of resins.If you ignore this requirement, the cost of internal finishing bath can increase significantly after the first guy."Miser pays twice", and, therefore, have to change the headliner bath.To not have to do that, just select quality materials - pine and spruce for the steam room is not exactly fit.But in the dressing room can be used to the full.
washing compartment in the bath
Modern washing compartment in the bath is a conventional shower, equipped with a couple of shelves for folding various small accessories.With interior design baths with their own hands, especially when it's about the washing compartment, water resistant material should be provided.This tiles for walls, screed, or tile - floor.These finishes washbay most durable and practical.In order for such sex was not slippery to walk, use a wooden or rubber mats coasters.
Installation of lighting in the bath
Banya is a fairly dangerous object in terms of electrical safety, therefore the maximum allowable voltage feeding the bulbs should not exceed 12 watts.
most often used in baths incandescent lamps and fiber optic systems.The LED in this case is not quite practical since not withstand high temperatures.
lamps used for lighting of all premises must be hermetically sealed to the inside does not leak moisture.Wires lay under a layer of insulation, pre-insulate them carefully.Switches should be placed outside the steam room.Wiring should be installed and mounted on the walls and ceiling before it is executed interior bath.They do this in order to hide the wires from mechanical damage or deterioration of the hot steam and long-term exposure to elevated temperatures.If the cables are led to the surface, they are hidden in a special box.
for baths, there are wooden, light diffusing lampshades.Place the fixtures in the bath on each side of the ceiling or along the walls.
In some cases, a lighting from under the seat backrests: the back is both a decorative grille for the light.Luminaires should not be much to light does not hit in the eye.
Beautiful scatter light emitting fiber optic lighting systems for saunas.These lamps are safe, because the lamp itself (projector) is located outside the sauna and in the steam room are only conducting light optical fibers.
With such a device, you can create the most unbelievable lighting options in a bath and a combination of colors.Do you want to - the starry sky, like - the aurora borealis, want - a flame of fire.Such lighting, moreover, economical and durable.
If you look at how the interior bath in the video, it will already know exactly what is behind what is done and how.The whole process is quite time consuming, so you need to be well prepared to explore all the steps to choose the right materials, and then proceed to the interior decoration of the bath.The price of such work would not be interesting to you, because you can do yourself.What you get as a result, will please both you and your loved ones for years to come.