Frame bath with his hands - an honorable way out of the situation when funds are limited, and have their own sweat lodge like.This design quality and the external beauty of the traditional structures of logs and brick is no different.Moreover, there is a lot of pluses, have caused the growing popularity of frame-panel construction.How can you resist the temptation to build a reliable bath as soon as possible and with minimal financial costs, which will serve faithfully for decades?
- Frame Bath: benefits
- nuances that require priority accounting
- Building carcass bath with their hands Laying the foundation
- Construction roof
- Internal and external finishing
- Frame bath with his hands: Photo Frame
- room with his hands: Video
Frame Bath: benefits
baths Since ancient times, made from chopped wood.However, the technology, proven for centuries, now has lost some relevance.And the cause is a new way - building frami
- minimum time of execution;
- possibility of building at any time of the year;
- no shrinkage;
- efficiency in the construction and operation;
- masking communications and electrical equipment;
- many variations of exterior and interior.
nuances that require priority accounting
frame and thyroid room with his hands is unthinkable without well-thought-out thermal insulation, thermal insulation because the proper conduct of activities - the best guarantee of creating favorable conditions for the normal sealing and ventilation.Better insulated with fiberglass or mineral wool, becauseThese materials have the impeccable performance, and therefore perfectly cope with their duties.
second point - vapor barrier.One of the major drawbacks of frame construction - the appearance of condensation.Moisture during snowfall and rain penetrates the cracks and accumulates inside the frame.To avoid such unpleasant phenomenon need to take care of the vapor barrier.The optimal solution - glassine or steam insulating film sandwiched between a layer of insulation and interior trim.Please note that the roofing material is not recommended - when heated it emits a sharp, unpleasant smell.
It is equally important to choose the right wood.Construction of the bath with his hands framing implies only well dried boards.Optimal in this case, linden, larch, aspen, which not only have low thermal conductivity, but practically not deformed.Molded to be top grade without defects.
Building carcass bath with his hands
Once you have decided on the place of future construction, you should do the following: analyze the composition of the soil, in the diagram indicate the location of the furnace, chimneys, ventilation, choose the material for the roof.Generally, elaborate draft framework bath - half the battle, so give this issue as much as possible.
Laying the foundation
Because skeleton bath has a low weight, the foundation is allowed to produce under the simplified scheme.One of the most profitable - pier foundation for asbestos-cement pipes filled with concrete.The sequence of works:
- buying asbestos-cement pipes (length - 40 meters, diameter - 100 mm);
- drilling (diameter - 200 mm Depth - 1.5 m);
- pipe cut in half, are inserted into the hole and covered with sand;
- preparing a solution (water, fine gravel, sand, cement);
- filling tube with the mixture.
initial stage stroitelsvo any framing bath - tying.This will require boards section 50x100 mm, pre-treated with antiseptic.To mark the wall, and then start laying on the outer contour.Boards put the outer edge and fasten them with nails.Socle is connected via piping supports.The top and bottom rail made of planks for flooring and roofing felt cut off the bottom of the basement.
horizontal stacking monitor the building level.Upon detection of abnormalities pads help of several layers of roofing.Set intermediate racks must be based on the subsequent installation of insulation and sheathing.To give structure and strength of tying logs attached by pre-walled metal plates.Turned out it is advisable to process piping with a special solution, which prevents decay.
With the construction of the wall is of great importance wheelbase.This figure should be equal to 0,6 m, provided that the arrangement of the opening and convergence with other walls not provided.Otherwise, the gap should be increased to 0.4m. The interval between the posts depends on the size of windows and doors.
Do not forget to build an additional stand in the place of attachment of the frame to the wall or bridge.After fixing all the elements nailed to check the squareness of the frame.The assembly begins with the formation of the angle.First collect the wall, which will be communicated with strapping.We check on the vertical and secured using temporary stays.Further it is necessary to set at a right angle to each frame.Trim boards are fixed, which are then nailed.To trim begin only after the completion of the installation frame.
roof truss construction going on the ground.Then, each of them should be raised to the roof and positioned on his desk.To facilitate the work on temporary lay beams overlap of thick planks.
desirable that the roof was vented.Between kontrbrusom and rafters stacked film, while a crate stuffed right on the boards.Roofing optimal ondulin.Gables closing pre-prepared sheets.You can now start to finish.
Internal and external finishing
As you can see to build a framework bath with his hands is possible.It remains only a final touch - finishing.Outside, you can sheathe siding bath, block House, fir or pine planks, plastered, lay tile.Under the trim stack waterproofing, and the void is filled with insulating material.
After the bath cladding work on the outside plaster.But before that you need to take care of the additional rigidity - upholster the walls of lath.
inner lining not paint - paint and varnish can be when heated give off noxious substances.For the production of rough ceiling used OSB plates, are fixed at the bottom of joists.The pair piers hide foil, the other walls are closing Pergamino.The ceiling is permitted to omit up to 2.2 m. This will upholster his "clean" lining of lime and make additional measures on warming.
Pay attention to the joints between the walls and ceiling - vapor barrier should extend 15 cm. Are nailed boards can be a variety of ways - urging them make choices in a groove or a quarter.It logs planks attached face, then set the oven and heating boiler.Do not forget about the rules of fire safety - a wall, fence off the steam room of the recreation area, is laid out from a brick.
Frame bath is ready!Subject to all rules, it will warm, comfortable and durable.This steam bath can become not only a place for hardening and relaxation, but also a source of pride - because you built it with your own hands!
Frame bath with his hands: Photo
Frame bath with his hands: Video