Today huge popular baths, built of laminated veneer lumber.These facilities do not require additional insulation, because the material has a low thermal conductivity.Glued laminated timber is endowed with high resistance, so the logs will last a very long time and safely.Important is also the point that for the construction of timber bath takes about six times less than the cash outlay.
- Production of laminated veneer lumber
- Design baths
- device foundation
- Windows for bath
- Finish bath
- Mounting roof
- Installing utilities
Manufacturinglaminated veneer lumber
Stresses bustling metropolis forcing more and more people to go into the countryside.But not all meet the one-day trip to the woods on weekends.A lot of time spent on the trip itself, after which there is a feeling of fatigue and noise, so this can not be called a full-fledged vacation.
More and more people are beginning to think about their ow
Many believe that the laminated board material acts as an elite, but this is very misleading.Glued laminated timber is below the log and does not require thick insulation, so the findings can make yourself: The cost of a bath of laminated veneer lumber is not so high.Another advantage is the high speed of construction.
If laminated veneer lumber impregnated impregnation plant, it will be less flammable, compared with other construction materials.It is also known that each tree is a source of essential oils and resins, through which air is curative.
This material can be made independently.You need to saw the wood into boards, process it, and dry it thoroughly sorted.Logs with defects such as knots or cracks is better to postpone.Then, the board processed substances that protect them from insects and rot.
Using a hydraulic press, the boards are glued to the board, while activated special adhesive, very strong.The inside of the timber is usually made of cedar, which is particularly decorative, and the central board to perform better from pine or spruce.The latter have a low density, but endowed with excellent insulating properties.
There are many technologies for construction of buildings of laminated veneer lumber.But in general, there are a number of specific nuances, which use the same methods of construction.Each room has a fairly simple design, elements of which may vary depending on the project, but the basis is always the same.Basic room bath, steam room and washing, endowed with high humidity and hot air.
If the bath is poor ventilation, the log can be covered with cracks.In this context, resistance of laminated veneer lumber is so high that even this nuance will not damage the quality.Try to think in advance all the elements that will be present in the room, so that later it was not necessary to rebuild the already finished.
We recommend that you familiarize yourself with the basic information that will help select the most appropriate building material.To do this, you can talk with professionals.You can also see different photos of laminated veneer lumber baths, learn how to look construction of laminated veneer lumber, to find the optimal size, number of windows, roof shape, and much more.
Pay attention to the place where your room is located.It is better to place such a project at a distance of 15-20 meters from the water, away from the roadway.It is necessary to build a bathhouse on the leeward side relative to the other buildings.Thanks to this arrangement, the house is protected from the slanting rain, swelling and damage to the tree.
At this stage, you need to accurately determine the number of tools that will be used during construction.Also build into account all the material that you might need in the construction of a bath.Calculate the amount of each material, their exact cost and the price of the bath of laminated veneer lumber.
If you find it difficult to do the job yourself, you can get advice of experienced professionals.You can buy ready-made set of bath at the factory, which will fully comply liked the project.After delivery, you need simply to collect.
Before using better materials to handle a rust inhibitor that can improve their resistance to moisture.Construction of the bath of laminated veneer lumber lasts about six weeks if all the materials are ready for construction.You can decorate the house inside or outside, or you can leave it as is.
construction of any structure begins with the installation of the foundation.Most builders prefer tape option.This type has many advantages compared to other.Tape version of the heavy weight, longer lifetime and is very easy to install.If you intend to build a house of laminated veneer lumber, you just fit the type of foundation.
If you plan to install heavy slabs, strip foundation is a great solution.It is located at a depth necessary for the ground floor.Experts note that the strip foundations should be placed 200 mm below the frost line.Thus, after the cold winter the foundation will not receive an additional burden and deteriorate.If the strip foundation will settle in sandy soil or dry, it can lay above the frost line.
not recommended to set the foundation on heaving soils or soil that is deep freeze.The technology of construction of such a foundation is very simple.To begin with, on the site layout work and then dig a pit.It is necessary to pre-determine the depth and dimensions of the pit.
After that, the works on installation of sand cushion.Its thickness should be about 200-600 mm.If necessary, training can be performed crushed rock.Then you can hold the device foundation for a house of timber.Next, you need to install waterproofing and blocks.
Before stack blocks must be cut from them mounting loop and the gap between them very carefully fill with cement mortar.This will help prevent water penetration.This option has a very simple technique, but it requires a lot of effort.So, the foundation is carried out on a layer of sand and gravel, which must have a thickness of about 10-20 cm. The very foundation is a monolithic concrete slab, which is laid insulation, protective layer of concrete and the contraction under the counter.
Chopped walls are horizontal design of the stacked bars that connect the corners notching.Log houses called frame house with such walls, and each row of bars is the crown.How is the construction of a bath of laminated veneer lumber?It should be on the lower side of each timber hewn groove that timber is placed on the plane of the previous round with a heater from jute and moss, one centimeter thick.
Crown timber at the bottom of the foundation is insulated with a special layer of deposited waterproofing.If you've never erected walls to watch training videos or to consult with an experienced, as is usually done in Canada, where the self-construction of houses at a premium.
There are more than fifty different pairings of wooden structures.The most common are the following options:
- «The paw" - the process of cutting angle without a trace;
- «The cup" - a procedure cutting angle to the remainder;
- «In a mustache."
You can perform frame for the bath, even in solid timber.To do this, you must connect to the dowel bars section 25x25 mm and a length of 350 mm, which are placed every 2 meters.Connections and corners of the internal walls are usually collected in the tongue or in the leg.Structures of timber require the free length of the walls, which should not exceed 6.5 meters.
If she gets more better to put vertical squeezing.Tow fit between joists.After installation, you need to caulk the wall slots.You can also perform a final caulking wall joints after a year and a half, since the wall will be able to settle permanently.
very easy going and a bath house of laminated veneer lumber, because all parts are prepared for production.Many compare this assembly with the children's game "building designer".Glued laminated timber does not require a special finish or cladding, although you can run it at its discretion.Special profiles can provide protection against blowing.
Windows for bath
for competent window installation by experienced builders erect them into thin slats and top and bottom doing a groove to fit the rails.Thus, the window can move freely up and down.Next, you need to warm grooves insulating materials and set casing.Final installation is carried out eleven months later, when the final frame gives shrinkage.
Attention!The steam bath and the washing should not use the wood of coniferous trees for the production of windows, because it has the ability to allocate the resin at elevated temperatures.
must install beams.
are two methods by which beams are attached to the walls: the use of metallic fastening systems and process of notching the wall beams.For the bath, of course, fit the latter.Overlapping should be securely connected to the walls of a wooden house, giving it additional rigidity.
As mentioned above, a bath of laminated veneer lumber does not require special finishing.You can just grind and paint the walls on both sides.There are several options for the bath floor.The most acceptable is a dual-layer concrete floor mineral wool insulation between the layers.Also, a good option is a wood floor in the bar.
you can beautifully decorate the waiting room, lounge and steam room.It is recommended to use alder, aspen or lime.It is very practical, because when heated it emits highly fragrant essential oils and helpful to health.Crate roof made of planks.When the roof, you can use the most suitable non-combustible material, such as Onduline, slate or metal tile floorings.
Do not forget about wall insulation, which is made on the outside and inside.Internal insulation is carried out during the construction of walls.Often this is done using elastic mats of fiberglass penoterm and aluminum foil, polyethylene film.These materials are both a vapor barrier.External insulation performed mezhventsovogo insulation.Remember that the floor and ceiling of the waiting room and the attic should insulate fibreboard.
After installing walls executed installation of a roof.To do this, you must build a truss system and make insulation of the roof.There are several options for installing a roof for a bath.It can be pitched or pent.Gable roofs are often performed during the construction of the private baths of laminated veneer lumber by hand.Such a roof is a very simple and reliable to manufacture.
You can make an attic as storage space in a bath - then you can use a mansard roof.Any type of roof consists of rafters (supporting structure), and the roof sheathing.Rafters are hanging and slanted.Inclined version overlap span up to seven meters without additional supports.Rafters will rely on the support beams or walls of the upper row.
When overlapping large span without intermediate supports should be used hanging rafters.Then you can proceed to install the flooring and building cornice gable trim weight.After that must be attached to the supporting structure of the lath boards and planks.
type battens will depend on the roofing material to be selected for the roof.Tiles will last a long time, but the material is quite heavy.It is better to choose for big houses with permanent residence and not for summer baths.For tile requires very strong battens and rafters.
slate roof weighs much less, but its service life is not more than fifteen years.With the construction of the value of lining one sheet to another must be equal to the value of a single wave.There are two types of laying: when the longitudinal edge aligned in a straight line and when they do not coincide.
can also perform a flooring of sheet steel material is the lightest of all types.Steel sheets can not be laid a solid layer as the inner side of the sheet will gradually corrode without air.Typically, two or three stacked sheets interconnected.They are attached to the crate with the use of special steel strips (-clamp), which are installed at a distance of 130-150 cm and placed in the middle of the sheet metal and in places close.
also need to do eaves, gutters and pipes that during rain or snowfall, the water could not flow down the walls.Ceiling bath may be made of different materials, which have high heat resistance and low thermal conductivity.The most the best option is a tree.
To install the utilities you can bring to business professionals, or do the work yourself.Water supply and sanitation should be present in any modern home.Development and implementation of an autonomous sewer system is very complicated and responsible work.Heating systems also need to be installed to stay in the cold.
power supply system requires high quality planning and quality materials that will meet all the requirements of the rules of electrical safety.Power supply baths and saunas refers to facilities of increased danger.The wires must be laid on the wooden walls in metal.
Remember that in the steam room for wires laid vapor barrier, as they have to rely on the conditions of high temperature.Lamps are usually installed in the bowl with insulation from moisture.Outlets and switches are installed only in rooms with normal humidity.
Plumbing communication are a number of water supply systems with distributing pipes for hot and cold water supply and water supply in the bathroom drains, water treatment equipment, water supply to the radiators autonomous heating system.
For air conditioners and air ventilation ducts must be installed and cut technology openings, and then perform a ventilation grille.You can also install smoke.Such actions can be done only by an experienced professional, so if you do not have experience in the installation of utilities, it is best to attract business professionals and remember all his actions.
If you have at least a small degree own carpentry craft, build bath of laminated veneer lumber there is no trouble.We hope that our recommendations will help you to understand the self-construction.We want you to gain valuable experience and to perform each step of the construction is perfect!