Such transportable on small wheels wooden chaise longue made using a circular saw with a disc thickness of 20 mm, which performs the sample timber for connections in a half-tree, and folds (photo 1), as well as slots (photo 2).Mounting Holes drilled parts sunbeds combined drill (photo 3), which allows you to immediately receive a screw counterbore.
Handles A deck chairs (see. Parts list and Figure 1) cut out of a band saw pasted on the blank template (photo 4).The same method is used in the manufacture of strips L cross deck chairs - glued to them with adhesive tape template (photo 5), and it will form the spearhead.M jumper spider fastened to the strips with screws 42 mm in length, which strips put on the workbench so that the tip is fully secured to the surface and are flush with the bridge.Through holes in the planks drilled holes in the bridge support and fasten them (photo 6).
The back cover plate N in the middle of the upper rib fillet cut out for the hand to pick up
sample on the circular saw spikes, side seams ...
... and grooves using a blade thickness of 20 mm.
Application of the combined drill holes for the screws.
Sawing the pattern pen loungers and ...
... cross bars.
assembly rails and bridges crossing.
fillet marking strip on the back.
Location of screws on the rear cover plate.
front rib supports G armrests and all the edges are rounded themselves armrests F cutter for R = 12 mm.Each leg is attached to the side of the armrest screws length 42 mm.
In both restrictive block to the lounger with the same pitch drilled support holes (photo 9).Then attach restrictive blocks to the average jumper J loungers screws length 42 mm.
According to Figure 2 are fixed two rear legs E to support the average length loungers screws 42 mm and the inner edges of the sidewalls A 64 mm long screws.Thereafter, the front legs D attached to the inner edges of sidewalls 64 mm long screws, and the front legs with the bridge - with screws to the legs of a length of 42 mm.
axis W Ø12 mm stainless steel is required for the rotation of the backrest.It is passed (photo 10) through both H backrest support mounted on a distance of 75 mm from the sidewall.
list of parts and materials
|C||Jumpers Front leg||1||-||38h89h482|
|J||average jumper loungers||1||-||38h139h482|
|K||limited.Blocks 2 loungers||-||38h38h482|
|P||Rear jumper loungers||1||-||38h89h520|
|addition to the evolving needs of the cross: M10h100 bolts and nuts (2 pcs.) and washers Ø25 (4 pcs.), washers Ø38 (2 pcs.), lockwashers Ø17 (2 pcs.) and washers axisØ38 (4 pcs.);threaded rod M 12 × 900 with bolts (1 set.);W axis stainless steel Ø12 × 500;wood screws for external works long 42 and 64 mm;double-sided adhesive tape;wooden stoppers;wheel Ø250 mm (2 pcs.).|
bar in the front of the deck chairs, ranging from pens, laid out on the side through the lining thickness of 12 mm and attach screws length 42 mm.
presses every bar back to its supports flush with their ends.Raise the back support up and check the gap between the sides and bar.Straps secured to the sidewalls with same a gap of 12 mm between the two screws 42 mm in length, and crosses to the backrest - 10 × M bolts 100 with nuts, washers 38 and Ø25 mm and spring washer through the through holes Ø10 mm (photo 11).
According to Fig.2 mark out the installation of support armrests and fasten them in place with screws 64 mm long: first - the closest to the back and then lay 89 mm and attached to each support.
rear headroom P loungers are fixed with two screws to the sidewalls of length 64 mm and check that its bottom edge was flush with the lower edge of the side walls and the side edges of the jumpers were flush with the ends of the sidewalls.
Insert the axle through the holes and secure the cover on it axis screws 64 mm long.Then, insert the axle through the holes in the rear legs, and between the rear foot and put the puck wheel Ø38 mm.Another put the puck on the outside of the wheel.Tighten the nuts (Photo 12), determine the final length and saw off its axis.
Finally, chaise longue cover waterproof varnish.
marking holes on the bounding box of sunbeds.
Eventually you get a wonderful, comfortable and cozy chaise lounge with your hands.Good luck!