So, you already know that the roof for the most part, are pitched and flat.
- Different types of roofs, their description
- cut of the roof with his hands
- Cover the roof with his hands
- As professionals laid metal: Video
- $ cost of materials
Different types of roofs, theirDescription
If we talk about pent, it almost always has a slope of at least 10 degrees.
Usually, the form of the roof and affect its functionality.It is this property and provides safe shelter home.Very rarely, the owners of private houses have resorted to building a flat roof, which is mounted to only one part of the house.This part may be reserved for the pool or the summer, open loft.
About gable roof can say a lot of mentioning its advantages and disadvantages, but first of all indicate that this type of roof has a lot of advantages in comparison with a flat roof.
This includes the possibility of organizing the attic into living, cleanabili
Important! Note that the gable roof got its spread due to the simplicity of installation and ease of calculations.
All parts are symmetrical and so the construction of the roof of this type is not particularly difficult.This is also called gable roof, or in the case of mnogoschiptsovoy few stingrays.Ramps may be different from each other area, have overhangs, and high tilt angles.This is called a broken roof.
usually sloping ceilings is symmetrical, with one break, which provides for a considerable volume attic.In this case, you have the opportunity to equip it under the attic.
if from different sides of the house calculations provide additional rays in the form of triangles, such a roof is most likely refers to the hip.This roof is simple calculations, but would require a lot of building materials.In addition, the room underneath should be high enough for the passage of a man in full growth.And if the owners want to equip it for year-round you should take care of the roof insulation foam, mineral wool or other insulation.
For the construction of a roof of corrugated you will need some tools and a bit of a different approach to insulation and soundproofing.
In the market there is a wide range of building materials for the decking of the roof type, and you can choose the one that is right for your building.
Important! Make sure to take into account that corrugated board is easiest to assemble the material, but at the same time requires a special approach to the heat, steam, noise, and waterproofing.
Even a little rain can not let you sleep, if Roofers decided to save on noise insulation layers.
cut of the roof with his hands
When installing the roof Decking to start roll roll waterproofing membrane in the valleys along the entire length.Leave allowances to the rafters, and the overlap of about 16 cm, the entire layer roll in the direction from the eaves to the ridge.
the inner surface of the rafters are attached vapor barrier film, cracks are sealed.
binder is usually used for water-resistant OSB thickness from 9 to 12 mm.She laid across the rafters.On top of the waterproofing to the rafters nailed kontrobreshetka.Crate stacked on top of the waterproofing layer.
Coating metal tile roof goes with the wave of her profile.Over it set strap end, exhibited by the level spanned by the cord and fastened with screws through each 2.5 meters.Sheets of metal are placed in groups of 2-4-6 pieces, depending on the angle of slope.Securing them at the ridge, leveled, and then continue along the entire length assembling.Extra overhangs trimmed jigsaw.
roof covered ondulin will last you a bit longer than of corrugated board, but is more expensive.This material has been extended due to its flexibility, weather resistance, easy installation and a wide range of colors.
It so happens that for the building, the roof should be made of the low-budget materials.In this case it is better to cover the roofing material.In this type of coverage, there are two ways: hot and cold.That is, using dowels, nails or blowtorch.The latter method is also called welding.
Important! When covering slate, sheets trying to puncture from right to left, providing an overlap into a single wave.In some cases there may be an overlap in the two waves.If the slate is placed in the longitudinal direction it is better to do a bottom-up, to ensure the overlap of the bottom row.
Cover the roof with his hands
during the overlap of the roof Decking sheets should lie freely and be clearly aligned both horizontally and vertically.The overlap depends on the slope of the ramp, t. E. What angle is greater than the overlap less.In this case, providing complete isolation from moisture.
When overlapping roof slate, sheets are stacked on a sturdy crate that strays from wooden sticks or dried boards 40-100 mm.Each sheet of roofing slate is based on three bars with the distance between them is not more than 700 mm.
For a snug fit and reduce gaps, Cornice final bar is raised using shims, and the same thing with every even doing a bar.
When overlapping metal tile roof slopes carefully measure and diagonal.If the roof has a bias, they are aligned with a straight line along the edges of the eaves.Made crate and kontrobreshetka.For the last selected timber 4-5h2,5sm.
As professionals laid metal: Video
view the following video, you'll learn how to stack metal roofing professionals.
$ cost of materials
choice of material always remains with the customer.
The table shows the price per 1 sq.m. roof for Russia and Ukraine.
|Material||Russia (RUR)||Ukraine (hryvnia)|