putty drywall - a mandatory phase of work with GCR. After installation sheets GCR, joints, corners, seams and fastenings place - entry into drywall screws - must be carefully proshpaklevat to align with the main surface of the sheet.
In addition, you may need a full plaster surface.In this regard, the question arises how to putty joints and corners with their hands properly as putty drywall full, under what kind of finish is necessary, what a starting or finishing putty is suitable for grouting and finishing layer.
- The putty
- Plastered ceiling plasterboard and plaster walls plasterboard
- putty joints drywall
- How putty drywall corners
- $ cost of work and material
- putty plasterboard, video
primary issue finishing Drywall - a putty filler, which filler is best and what luchshe.No between drywall putty and there is one important step - the primer.
the question "whether primed 'answer is clear - you need.Thus the choice of filler gets a choice of primer.But primer just need to choose depending on the material applied on top of it. Then plaster is desirable to choose paired with a primer (as recommended by manufacturers so materials).
The next question, if I have to take care of the fortress putty, can we putty mixture inside the front?Experts in one voice does not recommend such a "knight's move" because of harmful emissions such fillers that may affect the health of occupants.
Regarding the choice: dry or cook the mixture, then putty with their hands find it convenient ready, although most buys are dry mixes.
most popular filler and primer Knauf and Cerezyme.Among the products of Knauf, specially designed for drywall, a universal primer Tifengrund (its consumption - up to 100 ml / m.), Which does not require dilution.
Knauf Puttsgrund - also suitable for such work, its purpose - the use of plasterboard and other grounds under the decorative plaster.Universal Primer on Cerezyme - ST 17.
Putties presented Knauf can meet any need finishing drywall.
Knauf Fugenfyuller used during work on alignment and putty joints between plasterboard, concrete walls or ceilings.
Knauf Uniflot designed to putty the entire surface of sheets Knauf, putty joints, large scratches and attachment points.In some cases, the plaster can be applied without reinforcing mesh or tape, but it costs more expensive respectively.
Knauf Multi-Finish is used for leveling uneven grounds and spackling drywall surfaces for painting, wallpapering, or application of decorative plaster.
technology works - How to apply a primer and putty - is indicated in the instructions.Each product has its own characteristics, for example, a primer may be diluted or not, different mixtures of different drying time, application may also be nuances.Therefore preparation for putty GCR must begin with an examination of instructions.
Plastered ceiling plasterboard and plaster walls plasterboard
Plastered ceiling plasterboard and plaster walls of plasterboard have a sequence and method of execution.First shpaklyuyut seams, joints and angles, then embedded fasteners depressions.
How putty joints and angles correctly is worth considering in more detail.
putty joints drywall
Firstly than putty: putty joints drywall performed certainly not finish mixture.To fill joints putty suitable type and Fugenfyuller Uniflot.Overlay can perform the same universal putty or already finish.
Second, the surface must be properly prepared: circumcised on the edges of gypsum boards must be bevels - bevel to increase the area of the filling putty.Under each seam should be the middle of the profile (it should be taken into account when assembling the frame and FCL), the cap screws must be sufficiently recessed into the drywall, etc.
Third, as the putty: There are various options.Putty plasterboard joints is done by different masters in three main variations:
- butt glued to the reinforcing mesh or tape, after which the top coat is applied several times (applicable, holds, but the seam is empty, compared with other options less reliable);
- putty filled seam is aligned with the surface of sheets, fresh putty pressed mesh, excess putty is removed with a spatula, after drying it is applied to the second layer, which is glued paper tape, which carried over the finishing layers (applicable, fairly reliably, but it is very multi-layered);
- putty filled seam is aligned with the surface of sheets, glued to the plaster mesh or paper tape over the skim performed and leveling layer (medium variant - the most popular).
After drying putty should be sanded - the most smooth possible irregularities with the wall using a mesh or sandpaper.
How putty drywall corners
How putty drywall corners, like puttying joints, but has its own characteristics.
short, the plaster of the interior angles is performed by pre-glued paper tape on them, and the right putty outer corners can be planted on the first plaster reinforcing mesh, and then attach the top of the filler perforated angle.
Another important question - how to drywall putty before painting and other types of decoration, sure to completely putty entire surface after embedding the seams?Not necessary.
all depends on the type and density of the subsequently deposited material.If you have confidence in the fact that because of the decor will not shine in the plaster seams, it can not fully putty.
need for putty entire surface is, if even after grinding plastered seams stick out and to align them with the sheets GCR.It is also necessary to treat the entire surface putty GCR under the wallpaper.This is due to the unseemly prospect wanting to make repairs in the future, leave without drywall board, severing it with the old wallpaper.
$ cost of work and material
- putty plasterboard price in Moscow - 300 rubles / m;
- putty plasterboard works price in Kiev - from 50 hryvnia / m;
- Knauf Fugenfyuller (25 kg) putty plasterboard price in Moscow - 395 rubles;
- Knauf Fugenfyuller (25 kg) putty plasterboard, the price in Kiev - 85 hryvnia.
putty plasterboard, video