Repair - how much of this word.Repair ceiling - an integral and often very time-consuming part of the process.Of course, today there are many ways to make your life easier.For example, to make a false ceiling or tension.In this case, you will not be able to take care of the ceiling does not suffer its cleaning, preparation and leveling.
However, the ceilings do not suit everyone.The apartments with low ceilings, this method does not always take place, because even the minimum of 5 cm, which would have lowered suspension structure can become very tangible.So, have yet to return to the old antiquated way of renovation of the ceiling.
Of course, it would be great if the ceiling was perfectly flat.But this happens rarely.So before you finish you will have to align. alignment ceiling with his hands - quite a time-consuming activity, and not the most exciting. But if you're determined to self-align the ceiling, we can help you with this.
- What is the technology of alignment?
- $ alignment ceiling.Price
- alignment ceiling.Video
What is the technology of alignment?
First of all, we need to prepare the ceiling repair work.Otherwise, all your hard work and leveling plaster in a few months can apply to an empty phrase.
What we need to prepare the ceiling to the execution?
- Construction film
- warm water in a large number
- sponge or cloth
- Sharpening Kamel
- metal spatula 5-7 cm
- roller or brush (to taste)
Tools have now move on to the process of preparation.
- furniture to make the room better, but in a pinch, you can just cover it with foil construction.And, at the same time, cover the same film floor (to clean up after less).
- little trick - good spatula grind grindstone, it will be easier to tear off the old finish.But wide spatula is not worth taking, not to spend the extra power.
- Now, on to the dusty and dirty work - start otshkrebat old cover with concrete base ceiling.The case is extremely tedious, however, the output we still do not.Surfaces must be clean.If the room is large, you can go all day.In order not to be bored, gather your friends with a stock of anecdotes.It will brighten up a little work. During operation, pay special attention to the seams and joints with the walls. You have to undermine a spatula as it is blunt, so timber is not removed.
- When the previous stage will be finished, rinse with warm water from the ceiling remains of whitewash.Do not forget to change the water, not to be that you simply smeared over the surface of the lime.
- When peeled ceiling is dry, brush or roller process it Rotband Grund by Knauf (we advise you to plaster walls is Rotband because this brand has already established itself). primer provides a better grip with plaster surface and prevent it from further cracking.The seams and corners better handle brush.
- As soon as the ceiling is dry, it is ready to align.
If you have a little rest from the previous procedure, and the ceiling had time to dry out, turn to the most important stage of work - in fact, to equalize the ceiling.Well, if you do not have to level a lot.But if the ceiling is uneven, there are swings and pits, and the state ceiling leaves much to be desired, we will have a good sweat.But if you do it right, you will eventually get a lovely smooth ceiling.
again understand, what tool is useful at this stage:
- Water level
- Drill with mixer
- capacity to produce a solution
- Rule meters in length with two
- Special trowel for spraying solution
- wide spatula 60 cm wide
- Hammer and Hammer
And, of course, building materials themselves:
- primer (eg Rotband Grund from Knauf)
- Putty (Knauf Rotband-putty, which is available in two forms: Rotband-paste and Rotband-Finish).If you ask, the better to align the ceiling, experts advise this particular filler.
- Special dowels, screws
Align ceiling beacons allow you to perform the procedure efficiently.So, we have our ceiling cleaned and primed.Now we go to the alignment.
By the way, do you know that the optimal room temperature for the plaster is + 18/22 °, and the optimum humidity of 60%.When the base of the ceiling is dry, begin the installation of beacons.This process approach cautiously and carefully, as the case requires care.
You need to put beacons strictly vertically, so use a level.
on the back of the lighthouse Rotband apply a coat leaning against the wall and fix on it.The level should be pressed over the entire length of the lighthouse.
If the wall is too rough, then applying the solution to the flashing profiles may not be enough.Then apply the mixture as a vertical strip of width 3/4 cm and on the wall.After staking wall with a plumb and a cord of you figure out what is necessary thickness of the plaster layer.
permitting the length, use the two-meter rule, in which case you can put a beacon in increments of 1.8 m from each other.If the length of the walls up to 4 meters, then you have enough of the two beacons, mounted symmetrically.
First start plastering the space between the profiles and then the side of the wall.Support for the rule in this case would be the hardened plaster surface between beacons.
Prepare a mixture of plaster, then apply to the prepared wall wide spatula from the bottom up. at a time, apply the plaster from the lighthouse and next to the lighthouse, about a meter high. with aluminum pull rule section.And so every station.Remember, that the plaster Rotband quite malleable and can sag, ready to return to the site and hands it to the bottom.
smoothing plaster, you can start one hour after completion of the drawing.If necessary, repeat the procedure.After drying the ceiling, you can paste over the dark wallpaper.But if you decide to glue light and thin, it is better to apply two coats finishing putty that it does not shine through.
If you need to apply a thick layer of plaster, use reinforcing mesh.
$ alignment ceiling.Price
If you still decide to call the master, nice to know how much this service.
In Kiev, the cost of leveling the ceiling will be 35 USD per m2.Sticker grid 20 UAH lighthouse plaster 80 UAH and fillings from 55 USD per m2.
In Moscow, the alignment of the ceiling plaster beacons will cost 420 rubles per m2, and putty - from 350 rubles per m2.