most often carried out installation of LED strip on the ceiling, ceiling moldings, or other locations that can hide the fixing points LED strip.With regard to which of the premises can be made installation of LED lighting, no consensus: the kitchen, the hallway, the street ...
- Selection of lighting and its installation
- Installing LED strip lighting calculation
- and the choice of lighting
- Installation of LED lighting
- as a simple variant of the assembly
- Mounting LED strip: the cost of installation and the tape itself
However, there are a number of restrictions of a different kind that are related to the properties of LED lamps, and not with thethe physical possibility of installation.
Before make installation and connection it is necessary to make some rough calculations and decide on some things, namely:
- whether in the other room, say, standard coverage or not;
- installation of LED strip (with his hands or not - in this case it does not matter) requires an additional fastening elements, and so on. Etc .;
- whether in the presence of all that is necessary for the installation, if the installation will be done with their own hands.
Choice lighting and its installation
Terms installation of this kind of lighting, for example, profile, install additional, simple enough, but before you give up a standard lamp or chandelier should ask yourself the following question: "What ifLEDs burn out or burn them to the power supply? "Here we assume that the resources of the LED backlight to last long no matter what the installation diagram.
In terms of having the necessary tools and supplies all depends not only on the quality of the LED lamps, but also on what Arrangement will be used in a particular case:can be collected "with the world on a string", ie at the time when the installation of LEDs will begin to collect all the right;but you can buy everything with a set of LED lights, which in some cases is probably wiser.
addition, you should calculate the amount of tape that is needed to illuminate a room.Practice shows that 15 meters LED tape correspond with quite a high degree of approximation, power luminous flux of one ordinary incandescent lamp 200 watts.
Installing LED strip
Calculation of lighting and the choice of lighting
mounting LED illumination on the ceiling of a room or area is often used in the kitchen starts with the calculation of power consumption of the tape.
example, the packaging, the store or the manufacturer's website you can find out how many watts consumes 1 meter tape, for example, 7 watts.If it was purchased by 15 m, the total power consumption is 7 x 15 = 105 watts (which is less than the 200-watt bulb!).When using SMD LEDs, both white and RGB deviations from the nominal power consumption is practically absent;however, it may take account of the power consumed in addition to amplifiers.
fact that with all the pros power LEDs is a visible luminescence decay tape away from the source of electricity;This problem is "treated" solely due to the installation (and, of course, the acquisition) amplifiers.
In normal operation may also include a set of RGB the controller (if this tape RGB) and the transformer.The controllers can be operated with voltages from 12 to 24, and the input voltage step-down transformer - 220-230 V. The main indicator of controller is its power rating - usually it is somewhere in the region of 180 watts, while the power consumption of the transformer somewherethen 150 watts.Ideal scheme miscalculation necessary capacity looks like this:
Power tape & lt;Power transformer & lt;Power controller (if needed)
The greater the gap between the neighboring values (within reason), the safe operation of the particular site.
Installation of LED lighting
Installing LED lighting begins with the cutting of the ribbon;while the tape almost arbitrarily cut by 2, 3 or 4 parts - it all depends on where it will be installed.Incisions are made on special ribbon sections. at all locations cut the tape, it is necessary to clean contacts channels for subsequent soldering the connection cables.
Ways of cooked piece of tape can be different, but in most cases the use of a set of connectors, coming together with a ribbon, not very convenient - they should be replaced by more convenient, but their resistance (material) should be similar to the previous one.
further installation of LEDs, which have been collected into a single electrical circuit, may require outside help, because it must be completely raised to the required height above the ground if itwhat to do alone would be problematic.
At this stage, should be treated with extreme caution tape, which is not adapted to mechanical shocks and stress rupture.
Fastening tape would be less problematic if the whole extent of its mounting on the panels or walls, will be clean surface.
also important to periodically check the performance of the tape and in the event of any bugs or problems to eliminate them before the tape will be installed at its permanent location.
final stage of installation is to install the tape and masking of wires and transformers - in particular, the lights transformer can produce unwanted glare.In this case there is a special pad, closing the display panel, but does not prevent removal of heat from the device.
be taken into account when installing any detail, for example, should not be installed close to the ceiling, tape - reflected light is evenly distributed throughout the room space.By the way, if you place a tape evenly around the perimeter of the room, the artificial light will be virtually no shadows of people and objects - light evenly will fall as if from all sides.
We should also mention the colors of the light band of LEDs: white LEDs, even if their use is combined with a dimmer, do not give completely "white" light, which may not be entirely comfortable.In this regard, it is worth remembering that this sunlight (all colors of the rainbow in a single beam) and, as an option, consider purchasing RBG luminaires where saturation can be adjusted.
LED strip, installation (video review simple assembly variants can be found right here) tape, connect the power supply, the selection of the power supply and so on. D. Can be the main query to find materialstelling about the individual details of the selection and installation of LED lighting in any places and premises.
as a simple variant of the assembly
Mounting LED strip: the cost of installation and the tape itself
Of course, the price of different brands - LUNA, DELUX, FOTON, FERON, MAXUS, ARLIGHT - different, among other things, depending on whether it is, for example, whether the tape is resistant to moisture and what size she diodes;but how much is professional installation of one meter, that is without taking into account the cost of the LED lamps themselves, in Kiev and Moscow can be found fairly quickly:
- installation of 1 m in Kiev - from 15 hryvnia
- installation1 m in Moscow - from 200 rubles
likely that such systems of internal lighting systems are quick installation, where a relatively small amount of work, even if fastened to the ceiling or other hard to reach places.