Installation of shingles is a few basic rules, which will be described in this section.
- Materials for laying roofing
- Instruction laying bitumen roof shingles
- Tools Required
- Mounting batten
- Laying carpet backing
- laying cornice brackets
- Shingles stacking technology
- ShinglesStyling: Video
- Installation of shingles: Video
- $ Installation of shingles: the price
Materials for laying roofing
Required materials for the device roofs:
- carpet backing;
- ordinary tiles;
- metal brackets;
- bitumen adhesive;
- valley carpet;
- Konkovo-cornice tiles;
- roofing nails;
- seals conclusions;
Instruction laying bitumen roof shingles
Roof - is to protect the building from water, wind and snow, so you should remember that cover the roof should be as airtight as possible.
Before you mount the soft tile, is the standard solid roof battens.Above the rafters stacked sheets of water-resistant plywood or OSB as possible tight, solid
- to take a job or edging board;
- or moisture-proof OSB or plywood.
joints between the elements and the gap between the plates or boards should be no more than 4 mm in height and the run can not be more than 2 mm, and the material is selected clean and dry.
tools that may be needed during installation of the roof:
- conventional or pneumatic hammer;
- roofing knife;
- tin snips;
This is a very important part of the work on the roof, as it is durable and ensures perfect appearance after laying a plastic material.
How to put boards or planks in the crate?The work starts from the bottom up, and the material is placed first continuous strip at the lower edge of the roof, and then row by row to the ridge, subject to allowable clearances.
Based on this work with shingles is harmless and the system leads exhaust systems made holes and sealed exhaust elements.
Laying carpet backing
How to cover the roof of the carpet backing?Lining the carpet is used as additional protection against moisture.In addition, under that building materials can spend the winter, if the weather conditions do not allow to cover the roof with shingles.
Laying carpet backing - is a prerequisite for high-quality installation and tightness of the roof, it can be installed, both horizontally and vertically, overlapping 10 cm canvases with each other.
In the case of horizontal installation it is to start from the bottom up, overlapping, prokleivaya edge of each strip cloth, bituminous glue.
How to put a carpet underlay?The nuances of installation.
- Before you roll out the carpet backing should cover it and the edge of the valley fluff bituminous adhesive.
- Only after fixing the fabric cover and in the valley should start laying on a flat surface, cutting edge fabrics and carefully prokleivaya them across the width of the overlap.
After installation, you are finished with the carpet backing, the roof is in the context of the following structure:
- solid crate;
- carpet backing.
laying cornice brackets
Curtain strips stacked on top of the carpet backing
How to put the curtain strips?
- roof eaves and edges strengthened Cornice strip.This is to ensure that the material is not deformed due to the influence of temperature.
- Trims pre-cut and placed 5 cm overlap and then nailed nails or screws.
- at the junction of strips and secured with two nails for tighter rib structure.
Shingles stacking technology
Before starting work on the laying of tiles you need to cover all the valley carpeted similar in coloring with the color of shingles.Roofing material should be cut flush at the edge of the eaves and a good glue the edges.
flat strip on the eaves cornice tiles laid at a distance of 10-20 mm from the edge.Nailed this band is not necessary because the tape has a self-adhesive layer. in cold weather can be a little warm up band for the restoration of the building hairdryer viscosity adhesive base.
How to lay the shingles?Installation of shingles begins with the edge of the roof slope, eaves tiles on top.
In order to lay down the first line of tiles perfectly straight, you can drive into the ends of the roof of a small nail and pull the thread construction, thus keeping the same distance from the edge along the entire length of the roof, orraschertit straight line chalk for convenience.
recommended print multiple packages with ordinary tiles, shuffle the sheets with each other and nail roofing nails rows of tiles, previously removing the protective film, at a distance of 1-2 cm from the edge of the eaves tile, cut on the drawing.The projections should cover a number of subsequent cuts of the previous series.On skates cut cornice tile and nailed overlapping so that the nails were hidden under a subsequent sheet.
stacking sequence of shingles:
- solid crate;
- carpet backing;
- Cornice strip;
- cornice tiles
- ordinary shingles;
As you can see, knowing the basic rules laying shingles, installation is a snap to make with your own hands.
Shingles styling: Video
Installation of shingles: Video
$ Installation of shingles: Price Price
installation shingles depends on how well conducted preliminary work on laying crates, insulation layers, etc.The average cost of installation is:
- from 60 to 100 hryvnia in Ukraine;
- from 400 to 700 rubles in Russia.