door stopper able to prevent excessive plowing doors, protecting the walls from scratches and bumps.By putting such emphasis, you will always solve problems peeling plaster for interior doors or damaged wallpaper.Moreover, such devices prevent premature wear of the door leaf and the door handle.With the opening of a door stopper you can keep peace with the neighbors, because your door is no longer knocking on the wall and annoying.
- Installation of floor door stopper
- Installing wall limiter door
Installation of floor door stopper
include the whole range of door opening stops the most popular are floor models - simple but at the same time practical products.As a material for the manufacture of door stoppers of the type most commonly used alloys based on aluminum, zinc, copper and brass, and steel.
Brass has high anticorrosive characteristics so door hardware based on it does not rust, and remains attractive for a long time
easiest door stop can be made in the form of an ordinary pin, which is subsequently driven into the floor to limit the further course of the door leaf and its impact on the wall, as in the photo stop opening the door.These pins can be of different size and shape - they are high, low, flat, round, wide.Everything depends on the location of the door stop, door and other accessories, as well as the interior of the room.
Installation of floor door travel stop is recommended in the following sequence:
- preparation tool.When installing a door opening limiter with your hands, you will need tools such as a hammer, the usual drill, screwdriver and pencil.When purchasing a stop you need to check is included in the package to the door retainer special screws and dowels for fixing.
- Selecting a location for a door stop.The most important thing in this work - to choose the right place where you will mount the stopper.To do this, open the door and lock a door position that from her to stay close to the wall 5 centimeters.At the same time, make sure that the distance from the door to the wall was no less than the length of the handle, as in this case, Door hinges can not prevent the beating of the door against the wall.In determining the point of installation it is also necessary to take into account the purpose of the room - if you're installing restrictor opening interior door in the hallway, it's best to fix it as close as possible to the wall and not on the middle of the leaf.Do not install a door fence close to the ground to avoid the impact of the door lock the hinge.
- markup.You can then proceed to the marking of.To do this, mark with a pencil on the floor of the future placement of a door stopper.Before going to install it, you need to check it out again.Now you can safely close the door and start the prank holes in the floor.
- Making the holes.In the floor, drill two holes, one for fixing the dowel, the other - the pin.If you have a wooden floor, then do it would be easy enough, with a concrete floor will torment anymore.Make a hole in the floor covering made of tiles will be the most difficult, because at the time of drilling may be split off a piece of material, so it is advisable to mount the tiles fall into the seam.
- Fastening Opening angle of the door.After antics hole in one of them hammered dowels and door restrictor is put in place.It should look closely to the pin (guide pin) finished second hole.Then you can fix it with screws through the opening.After installation is recommended to stop once again to make sure that it prevents the door touch the wall or furniture.
- lacquered.To have kept the brass stops luster and shine, and does not darken with time, they decided to varnish.
Installing wall limiter door
Wall lock for the front door of a private house will be useful in the following case.Often the owners of the house wish the day was the open door for permanent ventilation.However, the door in the open position for a long time can not be, because it will permanently shut down by the wind.Here comes in the lock.At the bottom of the limiter is not set because it will stumble on households.Therefore it is expedient to make the top of the door lock.
Homemade angle stop when the door is opened it locks the door open at 90 degrees and does not give her to disclose more.Limiter door opening with their hands is easily manufactured from two plywood strips which have a width of 3 centimeters and the same length.One part of the lock is attached to the door frame, the other - is attached to the door leaf.Both components of the limiter are connected.
in place of their connection is inserted a steel cabin, which prevents the folding device and slamming the door.Fixing lock the door by means of brackets, which is screwed tightly to the door with screws.Catch a corner mounted freely.By analogy to the lock box is attached.
The principle of self-made stop opening the door as follows.Catch the full opening of the door is mechanically bend in the opposite direction.And if you suddenly stop vygnetsya not, then you can gently push it with his hand.If the door begins to close by the wind, homemade limiter will begin to take shape in the opposite direction, but the area that is installed in the fold, will prevent addition of, and the door will not close.To close the door when you go somewhere, or at night, you should bend the arm lock, and the door is closed without any problems.
Thus, no matter how beautiful and durable door did not seem, it takes a true functionality with fastening door hardware such as door opening limiter, which is a tool for the greatest ease of door.