If you have started a huge renovation in their apartment, the first thing you should pay attention to interior doors.Creaking, cracked, sagging, covered with several layers of oil paint - these doors are unlikely to add new design aesthetic.One solution - to perform the replacement of interior doors.
- preparatory phase installation of interior doors
- doorframe assembly
- hang door leaf
- Zapenivaem mounting foam
- final stage door installation
- Replacement glass interior door
- TrainingGlass Cutting glass
- Installing glass
preparatory phase installation of interior doors
on how much cash you want to invest in the repair of doors, and the price will depend on the replacement of interior doors.When buying an expensive solid wood doors without the help of a qualified professional for installation you simply can not do.And if you decide to buy the door veneer or MDF, and want to save more, what would perf
Also the door leaf, the door frame and trim you need the following tools:
- measuring tape;
- building level;
- electric drill;
- hacksaw on wood;
And also need to purchase the following construction materials - assembly foam, silicone or sealant, nails, dowels, wedges and spacers.
overlaid with all the necessary tools and materials, you can get to work.Start with the dismantling works.Using a chisel and a hammer in the first place, tear off the trim from the door frame, they are often hampered remove the door leaf from its hinges.Next, using crowbar, nail puller and paper board, remove the door itself.To do this, one end of the slip angle under the fabric, and the other end to push down - a process that will help lift the door and remove it from its hinges.With this method, you can perform the replacement fabric interior door.Then grab a hacksaw and Saw uprights half after using nail puller pull out opening the door frame.But this should be done carefully, without any special effort, otherwise it could lead to the destruction of partitions or walls.This demolition work completed.
The next step will be the preparation and assembly of the door frame.To do this, tape measure, measure the height and width of the opening.For these dimensions, cut the top rung and the two side plates.Collect the door frame must be in a horizontal position.The crossbar is cut from two sides at an angle of 45 degrees, and only two stands on the upper side.Adding the three elements of the letter "P", they must be interconnected exactly 90 degrees.If the exact degree, then using an electric drill with the side stand in the place of contact with the bar, drill hole 1 mm smaller than the thickness of the screw.The length of the screw is chosen depending on the thickness of the rack, plus 5 cm. To make one hole in the rack can be screwed screws.As the distance between the posts can be checked using leaf - between it and the box should be a clearance for the lock, this cut-out cardboard box length of 200 mm, a width of 20-30 mm and a thickness of 3 mm and temporarily between the door and lay the box.
When mounting the box in the opening you need to follow the uprights with a plumb.To fix it should be in each rack, and the wall, drill three holes and insert screws.
hang door leaf
Before you hang the door leaf must be attached to the rack loops and key-part of that crash with a chisel, and fastened with screws.To do this, at the door, stepping back from the top and bottom 20 cm attach the loop circle pencil and chisel do notches.Similarly, make recesses for hinges and front door frame.It is necessary to determine how to open the door, and with this in mind, choose the left or right hand hinge.But if you are still undecided on this issue, you can buy a universal loop.After the curtain installed and secured in the right place, put them on the door leaf.
Zapenivaem mounting foam
In the next step you need to zapenit gap between the door frame and the wall.With conventional spray, sprinkle on the perimeter of the door wall of ordinary water, it will improve the adhesion of plaster to the mounting foam.Doorframes obkleyte plastic wrap or a special masking tape so that it does not stain.Picking up the bottle with foam, perform termination clearance on three sides.To make better use of foaming quality professional assembly foam.Drying will take at least 3 hours, but the foam is completely dry after 24 hours.On one door unit takes an average of one cylinder.
final stage of installation
the next day you will find the final stage.Excess foam that protrude beyond the plane of the wall, must be carefully cut with a sharp knife.Then you can start the installation of casings, they must be washed down at 45 degrees to each other.Remember that frames are not installed flush with the door frame, hinge side need to pull back about 10-15 mm, and on the opposite side of 6-10 mm.If the trim is made of MDF, and the walls in your apartment perfectly aligned, you can secure them with the help of liquid nails.But for heavy wooden casings have to use metal nails so they will not have moved down, and remained in the place where you have fixed them.Choose finishing nails with a flattened hat size 1,4h40 mm.Deep inside the casing nails hammer at 1-1,5 mm, and that they are not noticeable, use a wax pencil the same color as casing.
Armed with theoretical knowledge, you can further watch the video on the replacement of interior doors on the Internet and proceed directly to the practice.
Replacement glass interior door
Replacement glass doors are mainly carried out when it is cracked or pobilos.The reasons for this may be different - the children played poorly or strongly slammed a draft.And it happens that you just want to change the design of the door leaf.Today, the market can pick up the glass for every taste and wallet - smooth or corrugated, clear or frosted, patterned or without any color.
operation to replace the glass in the interior door is complex and the simple person who does not have certain skills, it is best to consult a qualified technician.Private initiative can cause scratches and cracks, chips of glass.
Work to replace the start with the dismantling of the old glass.To do this, insert a chisel between the glazing beads and fold and press lightly, then pull out the chisel and return the bead in place.It's easier to pull the nails, hats which will stick out above the glazing bead.
The next step is to prepare the work of the glass - from dirt, moisture and other attacks.Rub both sides of cloth, if necessary, wash with a solution of baking soda.If you do not, the depth of recess is not large glass, and when breaking it could not crack the cut line.When the cutting of glass do not rush, think about where else will be useful extra crop.If we approach this issue rationally, remnants have simply thrown out.To do this on a simple sheet of paper you can draw the necessary elements of the layout and apply it according to the cuts on the glass.
Cutting of glass is performed by glass cutter and a ruler or a wooden rack.To do this, put the glass in a horizontal position, and then test the instrument on a small, inconspicuous area.It must be thin colorless band.If the feature rough and white, then you can throw a glass cutter.With a range of the glass, hold the glass cutter in a strictly vertical position and make an incision along the line leading roller and gently press.Each line is carried out only once.After the line marked, put the glass on the edge of the incision line of the table and press lightly.If done correctly, it should break.
When the cutting is necessary to remember that the width and length of the glass should be less than the distance between the seam binding three-quarters of the width of the seam.The gap of at least 2 mm is needed to ensure that the glass is easily included in trouble during the installation, as well as not to burst during operation of the door, as wood tends to swell.
before installing the glass cover must be cleaned from the folds visible dirt and old paint, and then treated with a special putty consisting of chalk and linseed oil.Glass set with the lower edge of the fold.Secure it with a bead, which is attached by nails.Molding fillet should be pre-cut to the required length and slaughtered each other at an angle of 45 degrees.After all glazing beads installed in its place, you can paint them.
If you want to make your door unique and unusual in that you will sandblasting glass.Experienced master strike pattern on the glass that you enjoy.